Techniques For Varnishing Your Painting
To “varnish” an acrylic painting means to add a protective coat or “seal” over your finished painting.
There are many reasons you would want to do this! You may be gifting or selling your painting or you simply LOVE your painting so much that you want to protect it for years to come. Adding that protective seal gives it that finished look.
Providing a protective seal will make the painting last longer because you’re protecting it from dust, debree and some fading from UV Rays.
There are some varnishes that can be removed years later so you can re-varnish a painting and make it last even longer! With that kind of varnish, you would apply an “isolation coat” and then apply the removable varnish over it.
I will not be describing that kind of removable varnish process in this post – only the permanent one.
My ABSOLUTE FAVORITE thing about varnishing an acrylic painting is that it can make the colors look richer and deeper because it adds a semi-reflective sheen to the entire painting. The satin and gloss varnishes add that extra wow factor to your painting especially with dark colors.
Reasons to not varnish your acrylic paintings are because you may want to paint over it at a later time. Maybe you don’t want to have any kind of sheen on the finished painting, although they do make a matte varnish. Or perhaps you simply don’t want the extra expense and time it takes to varnish your painting.
It’s okay to simply hang a finished acrylic painting up and not varnish it! I do it a lot. However, because of the reasons above, you may want to eventually varnish it to protect it for years to come!
In this post, I am going to show you how I varnish my acrylic paintings! I use the Liquitex Brush on Varnishes. If you are using something else, read the directions on the bottle to be absolutely sure and always test out a surface before adding it to your painting.
Okay let’s begin!
This post contains affiliate links.
How To Varnish Your Acrylic Paintings
Wait for your finished acrylic painting to dry. I would wait at least 24 hours because you don’t want to risk any thick under coats of the painting running through the sealer and ruining your painting.
Also if you are photographing your painting, make sure you do this before the varnish is applied! It can be tricky to photograph a painting that has been varnished because the sheen will make a glare.
I am going to demonstrate how I varnished my Moon Painting.
Before you begin… Test a little bit of the varnish on a surface other than your painting to see if you like the results and sheen! You’ll want to be absolutely sure because this is a permanent non, removable varnish.
Pour a little bit of the acrylic sealer into a shallow dish. I am using a Liquitex Satin Varnish in this demo. Then use a base coat brush to apply the first layers. I am using a base coat brush in this set. The bristles are very soft and it comes with two brushes. I labeled it on the handle because I don’t want to use that brush for anything else other than the sealer.
Lay your canvas painting on a flat, protected workspace.
There are different ways you can apply the varnish but I prefer running a straight even coat with the width of the brush. I do my first layer all horizontal strokes. The varnish I am using is very thin and fluid so it glides easily across the canvas.
You want to make sure you do the strokes all the way across the canvas and not stop half way in the middle.
Some artists like to make the strokes go with the strokes of the painting. This can add a nice looking effect to your painting, however, doing it this way is hard to make sure you have covered all of the canvas evenly.
Also, it’s helpful to work in a bright room or an area where there is a lot of sun shining through the window. Tilt your canvas to make sure you have applied each row evenly.
Although tempting, do not keep going back and keep re-applying your strokes. This can cause the varnish to sort of “peel” because it has slightly dried already.
Wait for this first coat to dry. The bottle says to wait 3 hours. While this first coat is drying, cover your shallow dish and brush with plastic wrap or clean and rinse your brush so the varnish doesn’t dry on your brush.
Add a second coat. I prefer going in the opposite direction of the first coat but you can do the same direction you used the first time. Again make sure you apply these coats evenly.
Wait for this coat to dry. If you want you can add a third layer, however, two coats is what I usually stick with!
It’s hard to capture on camera but it definitely made the dark colors in my moon painting more deeper and richer!
Varnishing your acrylic paintings will ensure your painting will last from dust and some UV Ray fading. I was able to sit down and varnish several paintings all in one session and it really didn’t take that long!
There are a few other ways you can varnish your acrylic paintings including a spray varnish.
I have tried spray Mod Podge on an acrylic painting. It was a very easy but messy process! However, I did not like the final results of it. It didn’t look even and the sheen looked a little “cloudy”.
Also, earlier in this post I mentioned you can do an isolation coat with a removable varnish. This only works with non-permanent varnish, the one demonstrated earlier is permanent and cannot be removed.
An isolation coat is simply a barrier between the actual painting and the varnish so that later on you can remove and reapply the varnish.
If you are interested in doing that method, look for a varnish that says “removable” such as this Golden one. Make sure you read the instructions on the bottle carefully before using it because I do not address that technique in this post.
That’s It My Friends!
It really is a simple process to apply a sealer coat to your acrylic paintings! Once you’ve done this several times, it gets very easy and you will gain more confidence in applying your coats evenly. It doesn’t take much time at all to do this and you have a protected painting!
Like Learning Beginner Painting Tips?
Share This Post on Pinterest!